Procedure A in ASTM D , has the objective to test composite laminates double-edged. The pin in the device, creating two cutting plans, extracts a segment. ASTM D TESTING FIXTURE – PROCEDURE B. FASTENER BEARING SPECIMEN SUPPORT. Pdf icon button Download PDF. The bearing strength of a . Model No. ASTM.D – Double Shear Fastener Test Fixture. The Double Shear Fixture applies a double shear load via two loading plates secured to the.

Author: Kilar Tygokus
Country: Algeria
Language: English (Spanish)
Genre: Sex
Published (Last): 7 August 2011
Pages: 28
PDF File Size: 14.71 Mb
ePub File Size: 20.53 Mb
ISBN: 926-2-36796-232-6
Downloads: 12362
Price: Free* [*Free Regsitration Required]
Uploader: Tojashakar

Procedures A and D, the x5961 configurations, with a single fastener loaded in shear and reacted by xstm tension or compression, are particularly recommended for basic material evaluation and comparison.

Have a question about conducting the test for this standard? Sometimes the customer has a requirement to test non-standard specimen sizes, requiring Wyoming Test Fixtures, Inc. The upper end of the fixture is held in a grip, as is the lower end of the test specimen.

ASTM D Double Shear Fixture for Bearing Composite Laminate | GDA

The fixture is shown in Fig. Procedures B and C, the single-shear, single- or double-fastener configurations are more useful in evaluation of specific joint configurations, including fastener failure modes. Standard specimen wstm using fixed values of test parameters are described for each procedure.

The properties obtained from this testing standard are the ultimate bearing d59961, the offset bearing strength and the stress-strain curve. The applied compressive loading induces a double shear in both the specimen and the loading fastener or pin.

Typically, Procedure D will yield slightly higher strengths than Procedure A due to the finite edge distance, ein Procedure A ; while Procedure C will yield significantly higher strengths than Procedure B due to the larger fastener rotation and higher peak bearing stress in Procedure B. That is, a single shear plane is developed in the loading pin as the tensile load is applied.

The range of acceptable test laminates and thicknesses are described in 8.

Each half of the fixture is 0. The other three procedures are pin bearing fixtures, as will be described here. The standard test specimen is 5. Properties, in the test direction, which may be asmt from this test method include the following: The free end of the specimen is held in a second tensile wedge grip. Note that the scope of this test method is limited to bearing and fastener failure modes.

  CURTIS SITTENFELD PREP PDF

An alternate version of the test fixture shown in Figs. Procedure D of ASTM D loads the laminate bearing specimen asrm double shear through a close-tolerance, lightly torqued fastener or pin. The composite material forms are limited to continuous-fiber or discontinuous-fiber tape or fabric, or both reinforced composites for which the laminate is balanced and symmetric with respect to the test direction. We offer machines, apparatus, testers, tensile grips, test fixtures, clamps, holders, jigs, faces, jaws, extensometers, environmental and humidity chambers, furnaces, baths and custom solutions for unique applications.

A is double-shear tensile loading, B is single-shear tensile or compressive loading of a two-piece specimen, C is single-shear tensile loading of a one-piece specimen, and D is double-shear compressive loading. The maximum force attained and the deformation of the hole in the specimen are recorded. The unstabilized configuration is intended for tensile d9561 and the stabilized configuration is intended for compressive loading although tensile loading is permitted.

ASTM D5961 Double Shear Fixture for Bearing Composite Laminate | GD5961-A

However, when fully documented in the test report, a number of test parameters may be optionally varied. Load at failure and hole deformation are measured. These Procedure B and C configurations have been extensively used in the development of design allowables data.

A tensile load is applied until a maximum loading has been reached, monitoring both applied force and hole deformation, as described in the ASTM standard. The standard configuration for each procedure is very specific and is intended primarily for development of quantitative double- and single-shear bearing response data for material comparison and structural design.

The range of acceptable test laminates and thicknesses are described in 8. Combining values from the two systems may result in non-conformance with the standard.

It is the responsibility of the user of this standard to establish appropriate safety and health practices and determine the applicability of regulatory limitations prior to use.

  DS26LS31 DATASHEET PDF

ASTM D Polymer Matrix Composite Laminate Bearing Strength Test Equipment

Force range of 5 kN to kN 1, lbf tolbf Adjustable test space The most popular choice for static tension and compression tests These dual column testers are available in both tabletop and floor standing models. For protruding head fasteners, Procedure D will typically yield somewhat higher results than Procedure C due to both stress peaking and finite edge distance in Procedure Cand Procedures A and C yield roughly equivalent results.

Referenced Documents purchase separately The documents listed below are referenced within the subject standard but are not provided zstm part of the standard. Sources of Additional Information:.

ASTM D 5961 TESTING FIXTURE – PROCEDURE B

Referenced Documents purchase separately The documents listed below are referenced within the subject standard but are not provided as part of the standard. Sources of Additional Information: However, when fully documented in the test report, a number of test parameters may be optionally varied.

However, the flexibility of test parameters allowed by these variations makes meaningful comparison between datasets difficult if the datasets were not tested s5961 the same procedure and identical test ast.

Procedure B is actually a specimen support fixture and is described in Section H-1 of this product catalog. Testing Procedure The test methods are as follows.

It is the responsibility of the user of this standard to establish appropriate safety and health practices and determine the applicability of regulatory limitations prior to use. The ASTM D standard describes several test procedures to obtain ast on the bearing response of pinned or fastened joints using multi-directional polymer matrix composite laminates reinforced by high-modulus fibers. Link to Active This link will always route to the current Active version of the standard.

Active view current version of standard.