The SEX is an S series solid body electric guitar model introduced by Ibanez in It was initially produced in Korea and then later in Indonesia. There’s no way a guy who does a couple guitar setups every day of the year would do a better than someone will with instructions from the. For over 18 years, Ibanez RG guitars with Edge double locking sys- tems have been SEX MOF. • 3pc Wizard II Manually Adjustable Zero. Point System.

Author: Votaur Tauzshura
Country: Honduras
Language: English (Spanish)
Genre: Education
Published (Last): 7 October 2004
Pages: 357
PDF File Size: 1.28 Mb
ePub File Size: 16.89 Mb
ISBN: 925-6-31547-722-6
Downloads: 53807
Price: Free* [*Free Regsitration Required]
Uploader: Shaktilkree

Adjust the saddle forward or backward to the proper position and tighten the saddle lock down screw. The Saddles are preset on the plate.

Loosen the string by turning the tuner and then remove the string. Open the new bushings at s520eex split section and snap them into place on the tremolo arm. Height adjustment is made by adjusting the 2mm allen screws on either side of the bridge.

The height adjustment of the tremolo can be set by using the two 4mm adjustment screws 2 on either side of the tremolo unit. The height adjustment of the tremolo can be set by using the two 3mm adjustment screws on either side of the tremolo unit. Raise or lower the tremolo to the desired string height using a 4mm allen wrench. Over adjustment can result in damage to the instrument and will no be covered under warranty.

| Help & How To

To check the intonation: To allow the arm to swing freely. The rotation torque of the kbanez can be adjusted by changing the number of bushings on the arm. To replace the bushings, remove the bushings by spreading opening the bushing until it is removed.

Tighten the pressure pad screws. The truss rod is adjustable at the headstock using as allen wrench or an adjustment wrench. Loosen the heigth adjustment screw 5 on both sides of the bridge using a 2 Phillips.

  DITRA HANDBOOK PDF

Adjusting the string Height.

If the intonation is still not correct repeat steps 2 and 3. TZ Bridges The Overall Tremolo height can be adjusted by raising or lowering the Height Adjustment screws 5 on either side of the bridge. The tremolo arm is placed in the hole in the bridge plate and inserted into the threaded block.

Ibanze and specifications are subject to change without notice. Loosen the pressure pad lock screws on the top lock with a 3mm allen wrench. It is sometime necessary to adjust the tremolo angle when new strings, different string gauges or different tunings are used. Tremolo Angle Adjustment The tremolo system should sit parallel to the surface of the guitar body, as shown in the illustration. On the bass plate there are two holes for each saddle lock down screw.

Adjusting the intonation is performed by moving the individual ibanezz saddles forward or backward. Loosen the Saddle lack down screw 9 on the saddle to be adjusted with a 2mm allen wrench. Turn the S520fx torqueadjustment nut turns counter clockwise.

Using a Phillips head screw driver, turn the Spring tension adjustment screw and adjust the length of the spring. Retune the guitar to s50ex proper pitch and check the angle. Thread the new string through the string holder tubeand over the saddle pulling it tight towards the headstock.

Make sure the manua rod is properly adjusted before adjusting the action. Insert the tremolo arm into the mxnual socket and firmly push down until the arm snaps into place Note: Loosen the string stopper bolt by using a 3mm allen wrench, and remove the string from the saddle.

Wind the string around the tuning machine and tune to pitch. If the 12th fret is flatter than the open note, the saddle needs to be moved forward.

Cut off the ball end of the new string above the string winding and insert the end of the string in between the main saddle and the string holder block.

  KRYSICKI RACHUNEK PRAWDOPODOBIESTWA I STATYSTYKA MATEMATYCZNA W ZADANIACH PDF

To reduce the torque, remove one bushing on the lower side. Always loosen the Stud lock screws counter clockwise with a 1. Solid Body Electric Guitars. If s520es 12th fret harmonic pitch is lower than the fretted note, the saddle needs to be moved back. When ibansz guitar is properly adjusted, tighten the top lock pressure pad screws 5. Intonation adjustment is usually necessary when new strings are fitted it can also be affected by the angle of the tremolo unit.

Loosen the string stopper screw 8 by using a 3mm allen wrench remove the string from the saddle. If manuap intonation is still not correct repeat steps 1, 2 and 3. When the guitar is properly adjusted, tighten the top lock pressure pad screws.

S520EX (2005–2009)

All lbanez guitars use A for a standard pitch. Before adjusting the intonation, first determine the direction that the saddle needs to be moved.

If the 12th fret harmonic is higher than the fretted note, the saddle needs to be moved forward.

Both bushings should be completely hidden. For ease in retuning, it is recommended that one string at a time nanual changed and tuned. To further reduce the torque, remove both bushings. Insert the tremolo arm into the arm socket and firmly push down until the arm snaps into place. Using a Phillips head screwdriver, turn the spring tension adjustment screw and adjust the length of the spring.

Turn the notched wheel 4 To raise or lower the bridge. Play the harmonic at the 12th fret, compare ibbanez to the fretted note at the 12th fret, these notes should read the same on the tuner.