LCD PROJECTION TELEVISION. KDFE LCD TV pdf manual download. Also for: Kdfe, Kdfe, Kdfe, Kdfe, Kdfe Sony KDFE – TV – Service Manual — Free Service Manuals. Download Manual for Model KDFE SONY LCD PROJECTION PartsDirect has parts, manuals & part diagrams for all types of repair.
|Published (Last):||7 July 2018|
|PDF File Size:||20.74 Mb|
|ePub File Size:||8.66 Mb|
|Price:||Free* [*Free Regsitration Required]|
Rear Cover Removal 15 It may take up to two minutes for the fans to stop.
Service Manual – Sony KDFE – TV — Download free service manuals
If the lamp is not securely reattached, the self-diagnostic function may be triggered and the POWER indicator flashes three times see page Warnings And Cautions Ne les remplacer que par des composants Sony dont le numero de piece est indique dans le present manuel ou dans des supplements publies par Sony. Do not touch the glass portion of the new lamp. Press the following buttons on the Remote Commander within a second of each other: Replacing the Lamp The Projection lamp, like all lamps, will eventually lose brightness and functionality, which affects the overall performance of your Television.
You agree not to post any material which is knowingly false, obscene, hateful, threatening, harassing or invasive of a person’s privacy. If the Self-Diagnostic screen is already displayed, proceed to step 3. Failure to do so may cause a fire or the screen to go dark. I have read and agree to the terms and conditions. Signal Flow Block Diagram 55 To avoid being burned, do not touch the lamp receptacle once the lamp has been removed.
Be absolutely certain that you have replaced all the insulators. B board – Fan connector is not securely attached.
SONY KDFE Service Manual download, schematics, eeprom, repair info for electronics experts
Remove 4 screws to detach the Screen Frame Assembly from the front bezel. Circuit adjustments that are critical for safe operation are identified manusl this manual. Expect required for routine service. Orientation of ring terminal should be towards the top of the set. A and other countries. Voltage variations may be noted due to normal production tolerances.
Free Service Manuals
Audio, Video, TV, Multimedia. Accessing Service Adjustment Mode.
Disconnect the CN from the K Board. Tape should wrap around bracket as shown to the right and securely hold the speaker wire so that it does not move once Wire Should be pulled so that there is no excess wire.
Using caution remove the LVDS cable and 2 screws. Replacing The Lamp Lamp maintains its brightness will vary depending upon your usage and environmental conditions.
The Lamp Hours and Panel Hours are shown in mnaual format. HB board is not seated securely, the TV-micro turns off the lamp. Lift out to remove HC Board. To maintain the quality of your viewing experience, Sony recommends that you kdg50e2000 the Lamp 1 after approximately 8, hours of use the TV will display a message reminding you to replace the lamp ; 2 when the screen becomes dark or the color looks unusual; or 3 when the LAMP indicator on the front of the TV flashes.
Sony KDF-46E2000 Service Manual
Look for unauthorized replacement parts, particularly transistors, that were installed during a previous repair. Expect some delay when ordering these components.
Check the line cords for cracks and abrasion. Ssrvice must be in standby mode. Doing so may cause the lamp to burst. Voltages are DC with respect to ground unless otherwise noted.
Remove as much slack out of wire before dressing it to the wire holder. Be sure to keep the retaining brackets.
When removing the Screen Frame Assembly be sure to clean the Mirror and Diffusion Plate s to remove any dust particles. To maintain the quality of your viewing experience, Sony recommends that you replace the Lamp 1 after approximately 8, hours of use the TV will display a message reminding you to replace the lamp ; To adjust various set features, use the Remote Commander to put the 1. The lamp is very hot immediately after use.
Les composants identifies per un frame et une marque sont critiques pour la securite. After completing all adjustments turn the set off with the Remote Commander and WAIT for the fans to turn off before proceeding to the next step. Gently pull kdf50e2000 Screen Frame Assembly forward. To print the manual completely, please, download it. Wait several minutes, then odf50e2000 the power cord.
Wait approximately 5 seconds until the data value is reset to 0. To change the Data Value, press 0 or 0 on the Remote Commander. Vibration can damage the lamp or shorten its life. Screen Frame Assebmly and Speaker Removal 22 1- Ne les mark kdt50e2000 critical for safety. Replace only with part number specified. II Purse lock should hold the mxnual